欢迎光临山东邹平中王机械设备官方网站!

关于我们|网站地图|加入收藏

全国热线: 182-6573-8111
当前位置:木材破碎机 > 行业知识 >

木材破碎机工作原理详解

文章出处:未知责任编辑:admin作者:admin人气: 发表时间:2019-01-02 10:17 字体大小:【

  木材破碎机工作原理是我公司在现有木材破碎机的基础上开发的新一代木材破碎机。它不仅具有一般木材破碎的优点,而且具有木材破碎产量大、破碎粒度可调的优点。也可根据客户需要在复合机上进行削木或碎木,克服了原有的送料原因。当物料速度快时,破碎效果不理想或破碎室堵塞,机器停止。

木材破碎机工作原理

  二。复合木材破碎机的工作原理

  启动机器,物料由进料输送机输送,根据物料特性调整进料速度。粉碎后,物料直接进入粉碎。破碎尺寸由筛孔尺寸决定。

  复合木材磨的分类

  根据进料特点,可分为手动进料和自动进料;根据出料方式,可分为带式输送物料和非带式输送物料,根据是否可移动,可分为移动式和固定式;也可按需要的。

  手动送料:设备有手动送料。送料速度取决于送料速度。

  自动送料:由送料输送机送料。可加装变频器调节送料速度。

  移动式:其它动力牵引,可在不同位置断木。

  固定式:固定在碎木位置;

  四、安装、调试和维护

  主机与电机固定在同一座椅上,主要是为了增强其稳定性。安装时,地面应平整,以保证主轮与电机轮对中,输送机应有适当的伸缩行程。辅机的安装可由客户根据现场情况决定,不存在任何安全隐患,不影响正常运行。

  连接件应填充密封垫。整个供电电路应由专业人员连接。启动前,系统应检查各连接部位是否松动,轴承等部位是否需要润滑,将机器指向转向是否与指示转向一致,检查完毕后再缓慢启动整个机器。

  1。开机前,木材破碎机工作原理应严格检查机器各部件的安装是否符合要求。金属物品不应落入机器内。首先,试运行时应使用手动皮带,检查是否有咬刹车、旋转壳体等现象,以免发生事故。

  2。开机顺序:先启动总电源,将机器点几次,直到正常开机。

  三。添加材料时,应保持均匀。严禁金属块进入下出口。

  4。在使用过程中,电机负荷不能超载,并保持正常运行。

  5。设备正常运行前,应先空载运行一段时间,并对各部件进行详细检查。如有异常,应及时修复,然后再卸载,直至设备能正常无负荷运行。

  6。应定期检查叶片和磨盘的磨损程序。如发现叶片、磨盘磨损严重,应及时更换。

  7。狼牙破碎机停车时,先停止主机,然后切断总电源。设备不使用时,木材破碎机工作原理应将设备各部件清洗干净,清洗更换轴承润滑油,并使用防尘屏蔽设备,以防雨淋和暴露。

  Composite wood crusher is a new generation of wood crushing machine developed by our company on the basis of existing wood crushing. It not only has the advantages of general wood crushing, but also has the advantages of large wood crushing output and adjustable crushing granularity. It can also make a machine in the composite machine for wood chipping or wood crushing according to customer needs, which overcomes the original reasons for feeding. When the material speed is fast, the breaking effect is not ideal or the breaking chamber is blocked and the machine stops.

  II. Working Principle of Composite Wood Crusher

  Start the machine, the material is conveyed by the feeding conveyor, and the feeding speed is adjusted according to the material characteristics of the material. After chipping, the material directly enters the crushing. The crushing size is determined by the size of the screen hole.

  Classification of Composite Wood Mill

  According to the feeding characteristics, it can be divided into manual feeding and automatic feeding; according to the way of discharging, it can be divided into belt conveying material and non-belt conveying material, according to whether it can be moved, it can be divided into movable and fixed type; it can also be combined in three ways according to need.

  Manual feeding: The equipment has manual feeding. The feeding speed depends on the feeding speed.

  Automatic feeding: Feeding is carried out by feeding conveyor. Frequency converter can be added to adjust feeding speed.

  Mobile type: other power traction can be used to break wood in different positions.

  Fixed type: Fixed in a position for wood crushing;

  IV. Installation, commissioning and maintenance

  The main engine and motor are fixed on the same seat, mainly to strengthen its stability. When installing, the ground should be flat to ensure the alignment between the main wheel and the motor wheel, and the conveyor should have an appropriate stretching stroke. The installation of the auxiliary machine can be decided by the customer on the basis of the site conditions, without any potential safety hazards and without affecting the normal operation.

  The sealing pad should be filled in the connecting parts. The whole power supply circuit should be connected by professionals. Before starting, the system should check whether the connecting parts are loose, whether the bearings and other parts need lubrication, point the machine to see whether the steering is consistent with the indicated steering, and then start the whole machine slowly after all the checks are completed.

  1. Before starting, the installation of all parts of the machine should be strictly checked to meet the requirements. Metal articles should not fall into the machine. First, the manual belt should be used for trial operation to see if there are any phenomena such as biting brakes and rotating shells to avoid accidents.

  2. Boot-up sequence: Start the total power supply first, point the machine several times, until the normal start-up.

  3. When adding material, it should be kept uniform. It is strictly forbidden for metal blocks to enter the lower outlet.

  4. In the process of using, the motor load can not be overloaded, and keep normal operation.

  5. Before the normal operation of the equipment, it should first run without load for a period of time, and check each component in detail. If there is any abnormality, it should be repaired in time, and then unloaded again until the normal operation of the equipment without load can be used.

  6. The wear procedures of blades and grinding plates should be checked regularly. If serious wear of blades and grinding plates is found, they should be replaced in time.

  7. When stopping, stop the main engine first, and then cut off the total power supply. When the equipment is not in use, it is necessary to clean all parts of the equipment, clean and replace the bearing lubricants, and use dust-proof shielding equipment to avoid rain and exposure.

排行榜

内蒙古木片机生产厂家「
内蒙古木片机生产厂家「
内蒙古木片机生产厂家 在接下来的十年里,印度有望成为世界上下一个巨大的木材纤维进口市场(仅次于中国)。由于国内缺乏
大型木材粉碎机粉碎后的
大型木材粉碎机粉碎后的
大型木材粉碎机 使废木材在生产生活中发挥了巨大的使用价值。随着科学技术的不断进步和发展,国民综合素质的提高,国

您的浏览历史